Accessories

Designed for comprehensive turn-up testing, monitoring and troubleshooting of fixed line, mobile, microwave and wireless carrier Ethernet links. UniPRO MGig1 is suitable for use on any backhaul link at speeds of up to 1 Gb/s.

UniPRO MGig1 allows enterprise users to monitor the actual bandwidth and performance compared to the agreed service levels from the service provider. It can also be used to stress test and monitor the performance of LAN backbone links.

Carrier users:

• Telco, cable TV, broadband, metro Ethernet WAN and leased line service providers
• Mobile network operators
• Data centres

Enterprise users:

• Managers of public utility, industrial, transportation, health care, education and financial networks
• LAN installation and maintenance personnel
• System integrators

Gigabit Ethernet multistream bidirectional transmission tester with single copper and optical ports and Y.1564

Kit Contents

1 x UniPRO MGig1 Solo Pro, 1 x NiMH Batt, 2 x Patch Cables, 1 x PSU with EU/UK/US adaptors, 1 x CD Manual, 1 x English Quick Ref Guide, 1 x Carry Case, 1 x Carry Strap.

Gigabit Ethernet Loop-back device with single Copper and Optical Ports.

Kit Contents

1 x NiMH Battery, 2 x patch cables - 30cm Cat5eSTP, 1 x PSU with EU/UK/US adaptors, 1 x CD manual, 1 x English quick reference guide, 1 x carry case.

SignalTEK 10G. SignalTEK 10G Display/Remote handsets, Li-ion Battery (2), Hanging Strap (2), Quick Ref. Guide, Carry Case, Power Supply (2), 2m Cat 6A shielded patch cables (2). (Includes Network Testing Features and Fibre Testing Features)

If you install, maintain or troubleshoot data cabling and Ethernet networks, SignalTEK NT allows you to prove the performance up to Gigabit Ethernet transmission rates.

By simulating actual network traffic users are able to test and document network and data cable performance to Gigabit Ethernet standards.

Where system warranties are not required the SignalTEK NT is a cost effective way of proving your copper and fiber networks provide error-free performance.

Transmission testing proves real performance

There is no industry standard defining the testing requirements of cable qualifiers, consequently passing a qualification test does not prove that the installed structured cabling will provide flawless data transmission.

Uniquely, SignalTEK NT utilizes a test method known in wide area networks as transmission testing to prove the performance of a network by sending real Ethernet data frames through the cabling and/or network devices to compare the error rate against the IEEE802.3ab Gigabit Ethernet standard. This provides a clear standards based Pass/Fail of the link being tested.

SignalTEK NT requires no configuration from the user as the two handsets automatically pair ready for testing; just select a usage scenario to simulate the appropriate service, from VoIP to CCTV, Video and web traffic.

Installation testing | Cabling:

• Network traffic performance test on copper and fiber to IEEE802.3ab standard
• Wiremap test for open, shorts, miswires and split pairs to TIA-568 standard
• Gigabit link verification for copper and fiber cabling
• Use a list of wiremap templates for common Ethernet cable types including CAT 6A/7A/8, and non-Ethernet cable, such as Profinet and ISDN.

Active network:

• Network load testing through switches simulating CCTV/IPTV/VoIP/Web traffic
• PoE/PoE+ verification that displays available voltage at device location
• Check Ethernet connectivity at device location to 10/100/1000 Mb/s
• Verify network configuration (device IP/gateway address/subnet mask)
• Switch port identification via LLDP/CDP protocols

• Distance to fault using TDR technology (copper only)
• Ability to identify and trace cables with a compatible amplifier probe (62-164)
• Optical power indication (with compatible SFP modules)

• Network load testing through switches simulating CCTV/IPTV/VoIP/Web traffic
• Stress test network before installing bandwidth hungry devices
• Port blink to visually trace cable from work area outlet to network switch
• Displays port ID of LLDP/CDP enabled switches to eliminate manual cable tracing

SecuriTEST IP is an installation and troubleshooting tester for digital/IP, HD coax and analog CCTV camera systems. With a single tester that can power, configure and document, SecuriTEST IP increases productivity from start to finish.

• Connect to various cameras using RJ45, Wi-Fi or BNC ports
• Power the camera with 12V from the Li-Ion battery or PoE/PoE+
• Faster camera login using the unique QuickIP™ function
• Comprehensive camera setup with aim, focus, PTZ, presets and network settings
• Provide proof of installation with PDF reports that show camera parameters and multiple video screen-shots
• Eliminate guess work with data cable and network troubleshooting tools